• Please do not post any links until you have 3 posts as they will automatically be rejected to prevent SPAM. Many words are also blocked due to being used in SPAM Messages. Thanks!

Search results

  1. J

    Post your WaterCooled PC pics here thread

    swiftech mcr320.it fit perfect. i seen a few others that installed with no problems . ive also seen the rx360 installed inside without any mod. 120x25mm fans will also fit inside and i put 2 fans on top with alil cutout of plastic. it slopes down towards the back so i would like to install...
  2. J

    Want to Buy WTB: MCW-G200 plate for MCW60, URGENT!ish..

    i just bought a gtx275 and ended up with the koolance waterblock. bought it from ppcs
  3. J

    Post your WaterCooled PC pics here thread

    My new build new rig figured i post pics. nothing special compared to sum of the pcs on this thread. Some help from sadasius on the loop thanks. Dual rad setup one loop. mcr320 and mcr220 mcp655, swiftech 7/16 hose 1/2 barb, bitspower nb/sb apogee gtz, koolance waterblock swiftech res...
  4. J

    Q6600 - are these temps normal

    i have a q6600 clocked at 3.2 with the swiftech apogee gtz ive tried a couple of ways of applying arctic silver 5, i tried the line the drop in the middle and applying it with a credit card. that i was using my temp are 37 34 24 26 at idle the best for me was the line across.
  5. J

    New OCing Numbers.

    i guess because you have a low vid for that chip, maybe that is why you are able to clock that high.
  6. J

    New OCing Numbers.

    Great overclock highest ive seen yet. i have to questions is that a 780i board? and what do you have the gtlvref lanes at if you dont mind me asking.
  7. J

    New case Cosmos s power switch problems

    i purchased a new cosmos s case, and installed the 24pin ext. cable when i hook up the power sw to the power sw on the motherboard the computer turns on and then turns off 3 seconds later. by itself. so the only way to turn my computer is to plug the pwer sw in and then pull it out then the...
  8. J

    Need help with my dual rad in a single loop

    yea im using the ext. cable that was included thanx though. the power on the switch stays on. i spoke to coolermaster there going to send me a new power switch, when they get more in stock, seems like other people are having the same problem.
  9. J

    Post Your Desk

    i try, theres definitly alot of guys out there with much better cable management, but i figure if you are guna have a side window might as well make it clean looking.
  10. J

    Post Your Desk

    just built a new computer figured i would share my desktop pic.
  11. J

    Need help with my dual rad in a single loop

    mostly done gota tighty up sum wires but have to wait for new power button for the cosmos s tell me what you think and if i should make any changes. as far as temps go they look the same when i just had the q6600 on water with the mcr220. so im happy for now
  12. J

    Need help with my dual rad in a single loop

    ok installed new mb boot up no problem. the only problem that im having now is that i dont think the button is working on the cosmos s everything is hooked up i have to turn it on with the mb power button. ill show a pic that i have stored of the new board. figured since i had to buy a new one...
  13. J

    Need help with my dual rad in a single loop

    i hear ya ur definitly right.
  14. J

    Need help with my dual rad in a single loop

    of course. ive been working on computers for 10 years.i am just new to watercooling as ive only done it on a few computers. and as far as leaks thats why i use hose clamps 1/2 barb with 7/16 tubing havent had a problem yet, fits nice and tight. i know people get leaks from time to time it...
  15. J

    Need help with my dual rad in a single loop

    i reseated the memory tried clearing the cmos, tried a different psu. just going to buy a new mb today.
  16. J

    Need help with my dual rad in a single loop

    no leaks.just the long beep of death. the motherboard,cpu, and motherboard were used in my old setup in my old case. after fooling around with it for a couple of hours i have given up guna try and order a new mb.
  17. J

    Need help with my dual rad in a single loop

    well got everything installed to make a test run. and got a long beep and then turned off. tried resetting the cmos but no luck tried removing ram no help tried removing video card no luck. maybe i should move this to another thread. the other funny thing is that the computer is turning on by...
  18. J

    Need help with my dual rad in a single loop

    everything arrived today. will post pics when im all done just want to finish this hopefully by the end of tonight. had to flip my top rad around barbs were gettinng inn the way of 1 of the hard drives.
  19. J

    Need help with my dual rad in a single loop

    thats what i was thinking. im guna have to goto the local pc store pick up a few things ill just add that to my list.
  20. J

    Need help with my dual rad in a single loop

    dazmode- most stuff came already, waiting for another rad, some tubing, nb block and gpu block,clips,lights, fans, fan extentions mosfet hs. -> coming from florida. sadasius- a t-line between pump and res as a drain? am i getting that right?jackquelegs-> thats also what i was thinking but would...
Top