discussion Rants etc.....

[clshades]

Yeah I don't mind doing it, it's more remembering to do it

My original Navien unit kept failing on the water flow sensor, I think it was just a poor design. I have a newer model Navien now that's been fine. I wouldn't say the water here in East York is "soft" by any means either, my humidifier gets pretty gross in the winter. Even though this newer Navien says its lower emissions, it still can smell a bit rich outside if it's short cycled. Not sure if that's common or not...

Granted we replaced furnace and went tankless together, but our gas bill dropped drastically in doing so. Also nice having "unlimited" hot water. Don't think it's paid off though, especially having to replace it once already, though I guess I could have just kept buying new flow sensor yearly. The gained floor space was helpful though since the tank was right in the path into the storage space.

I've always had issues with the Navians. Rinnai will slow flow rate to maintaining temperature. Navians sacrifice temperature to maintain flow which is why they have flow rate sensor issues. You'll always have more issues with Naivians when the incoming water temp drops. They flat out don't work at Big White.

 

[JD]

Rinnai will slow flow rate to maintaining temperature

Heh, I don't have much water pressure or flow to begin with, so I suppose it's good the Navien doesn't do that

 

[gingerbee]

well some hose's and vinegar bath doesn't sound that hard, if that is all that's need to run with really hard water, thanks CL

 

[Shadowmeph]

ok this is very strange I must be missing something thisis a sort of rant and mystery all in one
I pulled aprt a LED tv ( rca RLED5078 a-b) so I could check the LED strips but I didnt find any here's the thing though when I fired up to tv the RCA screen showed up for a few seconds also it was a TV from my work place so it was working , I am not sure if this TV actually has LED strips , when you pull off every thing you get to the White plastic there are two layers of then then there is a semi see through reflective plastic piece then under that there is a total reflexive silver piece then under that there is finally a thick one side is mildly abrasive piece that is see through oh I do have a rant unrelated I wished my cell wouldn't have hardcoded its name on all my photos

 

[sswilson]

Played my modded skyrim for the first time in a few months and everything went as per normal this afternoon.... went back for another round this evening only to find that the bloody AE version update installed and now SKSE won't run..... :-\

All is not lost yet.... there's a patcher out there on Nexus that supposedly puts it back to the way it should be.... we'll see if that's permanently broken my modded install.......

Hrmmmm..... so it worked up to a point. I was able to patch the original file and return to playing, but have now discovered that mounting horses is broken.... not sure where to go from here but I've backed up the phoenix flavour saves and am considering doing a fresh install to see if that does the trick. (I'll uninstall skyrim, re-install the new version, then apply the "fix mods" patch, and then try installing phoenix flavour over that.

 

[Izerous]

ok this is very strange I must be missing something thisis a sort of rant and mystery all in one
I pulled aprt a LED tv ( rca RLED5078 a-b) so I could check the LED strips but I didnt find any here's the thing though when I fired up to tv the RCA screen showed up for a few seconds also it was a TV from my work place so it was working , I am not sure if this TV actually has LED strips , when you pull off every thing you get to the White plastic there are two layers of then then there is a semi see through reflective plastic piece then under that there is a total reflexive silver piece then under that there is finally a thick one side is mildly abrasive piece that is see through oh I do have a rant unrelated I wished my cell wouldn't have hardcoded its name on all my photos

At a glance those all look like pretty standard diffusion panels to me. light are usually behind all of that stuff

 

[Shadowmeph]

At a glance those all look like pretty standard diffusion panels to me. light are usually behind all of that stuff

strange because under all of that is the metal frame no LED panels I actually even separated all of those plastic pieces to be sure the LEDs were not stuck in between hehe and here I thought that I had something to do today by testing the LED panels

 

[gingerbee]

shadow there is no LED's behind that ??? I ask because that just looks like the light diffusion layer you have there, are their LEDs hiding on the bottom/top/sides that would light that layer up maybe the only way I could see that lighting up the screen

ya, then it has to be on the bottom/top/sides light source

 

[Shadowmeph]

shadow there is no LED's behind that ??? I ask because that just looks like the light diffusion layer you have there, are their LEDs hiding on the bottom/top/sides that would light that layer up maybe the only way I could see that lighting up the screen

ya, then it has to be on the bottom/top/sides light source

I contacted someone on ebay and found that they are on the sides they are very small but very bright all I needed to do with plug it it and power it up it light up and I quickly found the one burnt out led now I am not sure where to get a replacement of either the whole strip or just the one LED anyone e know where to find parts

 

[Shadowmeph]

yes still ranting about the phone branding in all my photos its that every photo I take has the amour x 9 stamp on it which I do not like ,I take photos to see the picture not the amour x9 stamp imbedded in the photo SHot on Amor x9 WTH
ok huge
edit I feel stupid I relooked at my camera settings and noticed there is a option to turn off an on the watermark